
Part 1 of this series covered how we keep existing boilers, geothermal systems, and light commercial heating running. Part 2 covered the installation process for new home builds or remodeling projects. This post is part three of three and will cover how Janes Radiant creates our DIY Hydronic Heating System for DIY homeowners or contractors to be able to install these systems with confidence.
The hardest part of do-it-yourself projects is doing something for the first time and not knowing whether you have enough information to tell if you’re doing it correctly, and a hydronic heating system isn’t something you can call the average contractor down the street for help on. Sure, other companies will sell you copper pipe, boilers, and PEX tubing all day long, but knowing exactly how much you need takes precise knowledge and calculations, which makes hydronic heating installation a pain without the right support. That’s why Janes Radiant began creating DIY Hydronic system kits; we set each project up for success so the work is enjoyable, without the fear of messing up, and if you get stuck, you can call us for help!
Rough-In Kits: The Tubing Foundation

The rough-in kit includes everything you need to install PEX tubing correctly, built with the same process and equipment our professional crews use on the job. Before anything ships, a design expert reviews the project plans and dimensions and creates an easy-to-follow manifold and loop layout for installation. You’ll know where to set up your mechanical room, venting, and manifolds to kick off your project successfully.
What’s included:
- REHAU PEXa O2 barrier pipe, cut and packed in the right amount for the specific job, not a bulk roll and a guess
- A fully designed loop layout and installation manual, covering slab, staple-up, panel, and gypcrete methods along with tube spacing, mechanical room planning, and manifold setup
- A pressure testing kit, so leaks or tubing issues get caught before concrete gets poured, not after
- Tube cutters, crimpers, wire ties and/or staples, plus project-specific components like staple-up plates and aluminum panel systems based on the installation method
Mechanical Kits: Pre-Built, Pre-Wired, Ready to Hang
The mechanical kit is where we think we save a DIYer the most time and worry, and it’s the part worth understanding before anything else. We build every panel ourselves, pre-wire it, and calibrate it to the manifold in-house, with all the welding already done. That means the precise measurements and specs that usually make hydronic mechanical work intimidating are handled before the kit ever leaves our shop. On-site, the job comes down to hanging the panel, attaching the boiler, and connecting the PEX to the manifold. From there, the system is essentially ready to go.

Mechanical kits are available across a few configurations, sized to the project:
- Natural gas and propane systems, from 55,000 to 399,000 BTUs, suited to everything from small shops to snowmelt systems
- Electric boiler systems, a heating-only option for projects ranging from small rooms up to 5,000 square feet
- Panels for tank and tankless systems, built for homeowners heating a project off a hot water tank or tankless water heater, up to 2,000 square feet
- Heating-only or heating-plus-domestic-hot-water options, depending on whether the project needs the system to also supply hot water for sinks and showers
Radiant Heating System That’s Custom Designed, Built, and Shipped
We have built and shipped hydronic floor heating systems for projects of all shapes and sizes, from a small 300 sq ft greenhouse to an 8,000 sq ft barndominium and 16,000 sq ft athletic center. Every Janes Radiant hydronic heat kit starts with the actual project, and is not a one-size-fits-all box of tubing. We work with you to ensure the system is scaled for your project, uses your desired fuel type, and is set up to make install as easy on you as possible.
- Free consultation and full system design before anything is built

- Detailed, project-specific installation guide that walks through laying the PEX, pressure testing, setting up your boiler, and filling the system properly
- Pre-assembled and tested components, including pre-wired mechanical panels and labels to help you during install
- Phone support from people who actually design these systems, not a call center reading from a script
- Shipped directly to the project site, anywhere in the US or Canada
Self-installing a kit like this typically saves 40% to 60% off installation costs compared to a fully professional install, without giving up the design accuracy or part quality of one.
Who These Hydronic Radiant Floor Heating Kits Are For
Janes Radiant DIY kits serve two different kinds of customers:
- DIY homeowners tackling their own home improvement project who want a system that’s engineered correctly from the start, with support available if a question comes up mid-install
- Contractors who want a reliable hydronic heating system for a client’s project without taking on the design, fabrication, and calculation work in-house and just install it
Either way, the goal is the same: a heating system that’s correct on the first try, backed by a team that actually knows hydronics, not a generic supplier that happens to stock the parts.
If you’re planning a radiant heating project anywhere in the USA or Canada then you can start building your kit. We’ll walk through the project and put together exactly what it needs, nothing more and nothing less.